True Sense Technologies

1. Temperature Control Range(°C): -50 to +110
2. Resolution @-9.9°C to +99.9°C: 0.1°C
3. Resolution @all temperatures: 1°C
4. Accuracy: 0.1°C
5. Refresh Rate(s): 0.5
6. Supply Voltage(V): 12
7. Measuring Inputs: NTC10K
8. Cable Length: 0.5 Meter
9. Output Type: 1 Channel Relay Output
10. Capacity: 10A

Additional Information:

• Delivery Time: 2 Days

• DC 12V XH-M452 Temperature And Humidity Controller Module Digital Display High Accuracy Dual Output Automatic Constant Temperature And Humidity Control Board
• Set the temperature + : Normal display mode, long press the + key for 3 seconds, start temperature numerical flashing, press the + / - key to set values.
• If you do wrong operation ,it will return to detect temperature display automatically after 5 seconds .
• Set the temperature - : Normal display mode, long press - button for 3 seconds, stop numerical flashing temperature, press the + / - key to set value.
• Restore the factory Settings: At the same time long press temperature, and humidity + key for 3 seconds, digital display

Additional Information:

• Delivery Time: 2 Days

Additional Information:

• Delivery Time: 2 Days

• seamlessly Switch between the temperature modes (between cool and heat).
• Temperature is controlled by setting the temperature value and the difference value.
• manual temperature calibration is available.
• Refrigerating control output delay protection is built-in.
• An alarm outputs a warning sound when the temperature exceeds temperature limit or when the sensor outputs error.

• Front panel size : 75(L) x 34.5(W)(mm)
• Mounting size: 71(L) x 29(W)mm.
• sensor length: 1m (include the probe).
• Product size75(L) x 34.5(W) x 85(D)mm.

• Temperature measuring range: -50 – 99°C.
• Resolution : 0.1°C.
• Accuracy : ±1°C (-50 – 70°C).
• Sensor error delay: 1 minute.
• Power supply: 220VAC±10%, 50/60Hz
• .Power consumption: ≤3W.
• Sensor: NTC sensor (1PC).
• Relay contact capacity : Cool 10A/250VAC;Heat 10A/250VAC.
• Ambient temperature : 0 – 60°C.
• Storage temperature : -30 – 75°C.
• Relative humidity : 20% – 85% (No condensate).

• High Performance 
• Dual Display, 4 Digit, 7 Segment LED
• LED Status Indicator: Relay ON, Tune
• 3 Front Panel Control Buttons 
• TC / RTD Input 
• ON-OFF, PID, PID Autotune 
• Two Setpoints 
• Control Output: Relay or SSR Drive
• Alarm Output: Relay or SSR Drive

Additional Information:

• Delivery Time: 3 Days

• Inputs: Thermocouple: J, K, T, R, S; RTD: PT100; Signal Inputs: -5 to 56 mV, 0 to 10 VDC, 0/4 to 20 mA; Resolution: For Temperature input: 1/0.1 °C / °F; For signal input: 0.001, 0.01, 0.1 & 1; Accuracy Temperature: 0.25% of span ±1°C (20 min warmup), Signal input: 0.05% of span ±1 digit
• Display: 4 digit, 7 segment LED : 0.5; LED Indication: None; Display: Messages Over range/Under range/Open sensor/TC reverse
• Sensor Supply: 24V DC, 30 mA; Supply Voltage: 85 to 270V AC/ DC (AC: 50 or 60 Hz)
• Operating Temperature: 0°C to 50°C; Storage: -20°C to 75°C; Humidity (non-condensing): 95% RH
• Protection Level: IP65

Additional Information:

• Delivery Time: 2 Days

1. The display is red, it shows three “LED” digits,Clearly shows the temperature full value (no decimal place) .
2. Below the display are Four buttons which control the humidity controller. First buton is “SET”  with next two buttons are + and – are used for menu navigation increasing or decreasing values, and Rst is “ON/OFF button”
3. On the back of the humidity controller  3x green terminals. In left is “Relay switch” , in center is “Power” and right is terminals for probe AM2302. (Later i descripted in schematick)
4. The sensor for the Humidity controller MH-13001  is placed in bottom of temperature controller right side .It is about 80 cm long with active end.Type of temperature sensor is AM2302.
5. Humidity controller MH-13001  can save the setings if no power source (blackout).