True Sense Technologies

The DO-66 type pen type intelligent Dissolved Oxygen Analyzer is designed to facilitate the user to carry the operation on the spot. The instrument can be divided into two parts: the sensor and electronic unit. The sensor adopts thin film dissolved oxygen electrode. The electronic unit is an integrated operational amplifier + microcomputer chip with automatic temperature compensation function.

Technical Specification : 

1. Measurement Range: DO: 0~199.9%; 0~16.50mg/L  Temperature :0~50 32~122
2. Resolution: DO: 0.1%; 0.01mg/L  Temperature :0.1 32.18
3. Accuracy: DO: ±1.5% F.S  Temperature :±1 33.8
4. Residual Current: No more than 0.15mg/L
5. Response Time: No more than 15 seconds
6. Temperature Compensation: 0 50
7. Power Supply: 2 *AAA batteries
8. Working Temperature: 0 50
9. Dimensions: 207*32*36mm
10. Weight: 85g

How To Use :

1. Installing batteries.
2. Connect the DO electrode to the corresponding input. 3.Press ON/OFF key to turn on the machine, take off the electrode protector and insert the electrode into the solution to be tested.
4. Press [% and mg / L] key for % and mg/L display conversion.
5. The dissolved oxygen concentration of the solution (mg/L or %) can only be read after the display of the instrument is stable.
6. Press the ‘°C/°F’ key to switch between Celsius and Fahrenheit.
7. Press the ON/OFF key to turn off the power.

Calibration 

1.Rinse the electrode well with DI water or rinse solution. press ON/OFF to turn on the machine. Dip the electrode into the zero oxygen solution for at least 3 minutes, and keep shaking gently until the display value stabilizes.
2. Press and hold the ON/OFF key until the second line of display shows "CAL" character, continue to shake the electrode gently, when the display value is stable, press [% / L/mg] key, it shows DO value 0%, complete the zero calibration.
3.Clean the electrode, dip the electrode into the saturated dissolved oxygen solution and keep shaking the electrode gently until the displayed value is stable.
4. Shake gently and press ON/OFF key until the second line of the display shows "CAL" character, then press  F key, the DO value of 100.0% is shown at this time, the slope correction is finished.
*Note: If you accidentally enter the calibration state (the second line displays CAL characters) due to an operation error, press the [ON/OFF] key briefly to exit.

Supplementary Note For Calibration

1. Preparation of oxygen free water Configure 250ml of 5% sodium sulfite solution, you can add the right amount of cobalt chloride as a catalyst.
2.preparation of saturated dissolved oxygen water Take 300 to 500 ml of distilled water, at a relatively stable temperature, use an air pump to aerate the distilled water for at least 15 minutes.

Additional Information:

• Delivery Time: 2 Days

Additional Information:

• Delivery Time: 2-3 Days

• Display : LCD size : 29 mm x 28 mm Dual function LCD Accuracy : Dissolved Oxygen:± 0.4 mg/L.L, Oxygen in Air:± 0.7% O2, Temperature:± 0.8 ? /1.5 ?
• Resolution : Dissolved Oxygen:0.1mg/L, Oxygen in Air:0.1% O ² Temperature:0.1 °C. Data Hold : Freeze the display reading. Operating Conditions : Temp:0 to 50 Deg C,Humi:Less than 80% RH.
• Operating Range : Temperature:0 °C to 50 °C (32 °F to 122 °F) Humidity: Max. 80% RH. Power off : Auto shut off saves battery life, or manual off by push button

Additional Information:

• Delivery Time: 2-3 Days

Additional Information:

• Delivery Time: 2-3 Days

1. Professional Water Quality Meter: 3-In-1 Digital TDS meter provides accurate readings for TDS (Total Dissolved Solids) EC (Electrical Conductivity) and temperature. Professional, Accurate, and Precise 3-in-1 TDS, EC, and Water Temperature Meter. The TDS meter has automatic temperature compensation in measurement mode. 9 minutes no operation, the meter will automatically shut down. Save power, extend battery life.
2. MULTI-MODE CONVERSION: TDS, EC and Temperature Meter, TDS instrument a total of 4 different modes, press the SHIFT key can be converted between different modes. Mode memory function, each boot mode is the default mode used before the shutdown.
3. Measurement Range: Features with a sensitive electrode sensor to help you get accurate readouts. Measuring range is 0-9999ppm with ±2% accuracy, while the temp range is 0.1-80.0°C (32.0-176.0°F). Press SHIFT button, display changes: TDS – ppm & °C, EC – µs/cm & °C, TDS – ppm & °F, EC – µs/cm & °F. 10 minute Auto-Off feature.
4. Locks your reading making it easy to record: Large, easy to read LCD screen and data-hold function makes reading and recording a snap. “HOLD” automatic locking, “SHIFT” automatic conversion, 5 minutes Automatic locks.Press the SHIFT key while the value is locked to view the measurement results for the different modes. The measurement time is rapid, due to the exquisite naked type sensors, 5 seconds complete.
5. A Essential Tool For Every Household: Instantly check on the overall quality of the water you and your family drink. Know if your tap water purification system, such as reverse osmosis (RO) works properly or needs replacement, protecting your and your family’s health! Know when is the time to change filters, maintenance the aquarium, add nutrients or remove contaminants from your water!

Additional Information:

• Delivery Time: 2 Days

• Dissolved oxygen meter is a precision instrument for measuring dissolved oxygen and temperature. The dissolved oxygen probe is a thin film with a polarographic sensor and a thermistor for temperature measurement and temperature compensation. The permeable membrane separates the measured solution from the sensing electrode but allows oxygen to pass through the membrane to react, and the concentration can be measured.
• Dissolved oxygen refers to the concentration of molecular oxygen dissolved in water, generally expressed in mg/L (ppm) and saturation percentage (%), which is the percentage of dissolved oxygen in 1L of water. The oxygen concentration of our dissolved oxygen meter is 0.0-40.0mg/L, most of the range of dissolved oxygen meters on the market is 0.0-20mg/L. When measuring and calibrating, needn''t open the protective cover of the electrode, just put the electrode in the solution for measurement.
• Detachable probe, easy to replace, equipped with 6 probe protective covers. The film inside the protective cover cannot be taken apart. After using for a period of time, the test value is inaccurate and the calibration is still inaccurate, and the membrane sleeve needs to be replaced.
• Adopts the digital screen display with backlight, which is more clear and convenient to read data. Auto power-off in 8 minutes if not using it. Low battery indication. Oxygen solubility will be affected by temperature, atmospheric pressure, and salinity. Our instrument with temperature compensation can meet normal use.
• It is very suitable for measuring the dissolved oxygen level and temperature in a wide range of aquariums, swimming pools, ponds, freshwater aquaculture, marine aquaculture, school teaching experiments, laboratory sterile environment, aquaculture, scientific research, and other fields.

Additional Information:

• Delivery Time: 2

• Model Number: JPB-70A.
• Type: Portable Dissolved Oxygen Meter.
• Measurement range: 0.0 to 20.0 mg/L.
• Accuracy: 0.3mg/L.
• Resolution: 0.1
• Residual current: not more than 0.15mg/L.
• Response time: no more than 30s (90% response at 20°C)
• Automatic temperature compensation range: (0 ~ 40) °C
• Measuring range:

• LCD
• Automatic temperature compensation, fast response time
• Portable, easy to carry
• With our factory dissolved oxygen electrode (polarized film type)
• Power supply: 1.5V button battery (4)
• Dimensions (mm): Φ40*185 (without electrodes)
• Size:185(mm)
• Weight: 88g
• Instrument keyboard description:
• Key Function
• (switch) power on and off.
• CAL calibration key (long press 5 seconds to enter the calibration interface)
• HOLD lock/hold key, Fahrenheit/Celsius temperature conversion key.
• JPB-70A pen-type intelligent dissolved oxygen analyzer (hereinafter referred to as the instrument) is mainly designed to facilitate the user to carry on-site operation. The instrument can be divided into two parts: sensor and electronic unit. The sensor uses a polarographic film-type dissolved oxygen electrode. The electronic unit is composed of high integrated circuits.The instrument uses a dot-matrix liquid crystal display to display dissolved oxygen values and temperatures.

Additional Information:

• Delivery Time: 2

Additional Information:

• Delivery Time: 2 Days

• Slim, ergonomic design with rounded edges and a case that is only 17 mm (0.7 inch) thick, the HI98301 is thin and fits comfortably in the hand or pocket
• Large multi-level LCD, the LCD is 29 mm (1.125 inch) x 20 mm (0.81 inch) allowing the user to easily read both the pH and temperature simultaneously
• Two-button operation-one for On or Off, the other for calibration
• Exposed Temperature Sensor: Exposed temperature sensor allows for quick automatic temperature compensated measurements
• Temperature can be displayed in either degree Celsius or degree Fahrenheit

Additional Information:

• Delivery Time: 2-3 Days

• ORP is the abbreviation of English.
• It represents the oxidation potential of solution.
• ORP value is a measurement index of redox capacity of aqueous solution, and its unit is mV.
• ORP meter is a special instrument for measuring redox potential of solution.
• Oxidation-Reduction Potential in The waterproof design of the outer shell of the instrument is IP55.
• The electrode can be replaced.With data locking function. It is convenient to save and record measurement data.
• Negative Potential (O.R.P) PenThe introduction of advanced technology and imported components has greatly reduced the volume, reduced the cost, and maintained the original good quality, making the use of O.R.P universal.
• It is suitable for the determination of negative potential value of functional energy water purifier with negative potential, energy water cup and other requirements.

Additional Information:

• Delivery Time: 2

• TDS/PH/EC/thermometer 4 in 1.
• Measuring range: pH: 0.00-16.00 ph; TDS: 0-19990 ppm; EC: 0-19990 μs/cm.
• Resolution: 0.01 ph; 1 ppm; 1 μs/cm; 0.1 ° C; 0.1 °F
• Accuracy: ph: +/- 0.01 ph; TDS/EC: +/- 2%; temperature: 0.5 °C
• Battery: 3*1.5V LR44 button battery (not included)
• Temperature: 0.1-60.0 ° C; 32.0-140.0 ° F
  
  Calibration: ph: three-point automatic calibration (6.86 & 4.00&9.18 ph); TDS: 1413 μs/cm; EC: 1413 μs/cm
  
  
• Auto off: 5 minutes
  Multimeter can help you read data more accurately.
  When purchasing a multimeter, please pay attention to the parameter information of the product.

Additional Information:

• Delivery Time: 2

• Taking TDS MeasurementsRemove the protective cap.
• Turn the TDS meter on. The ON/OFF switch is located on the panel.
• Immerse the meter into the water/solution up to the maximum immersion level (2 inch).
• Lightly stir the meter to dislodge any air bubbles.
• Wait until the display stabilizes. Once the reading stabilizes (approx. 10 seconds), press the HOLD button to view the reading out of the water.
• If the meter displays a flashing x10 symbol, multiply the reading by 10.
• After usage, shake off any excess water from your meter. Replace the cap.
• Taking Temperature MeasurementsOnce the meter is on, the temperature function can be used at any time, in or out of liquid.
• Press the TEMP button. The display will switch to temperature (in Celsius only).
• To return to TDS mode, press the TEMP button.PrecautionsThe meter is not water-tight. Do not dip the meter beyond the water level limit.
• Do not store the meter in high temperatures or direct sunlight.
• Do not attempt to open the housing or tinker with the electronics of the unit.
• After multiple usage, if the product is not showing correct readings, please use the recalibaration guidelines as given below.
• Re-calibration GuidelinesImmerse the TDS Meter into Calibration solution up to maximum immersion level (2 inch)Reading appear on the Display.
• If the meter does not read within 2% of solution. Press Temp key for 3 seconds, Display Start Blinking. Adjust the reading by using “Temp” key (to increase the reading) and hold key (to decrease the reading)Press Temp key again for 3 seconds, meter enters in Testing Mode. Take the TDS Meter out from water Wait a moment, after showing Zero put the meter again into water. TDS Meter show Readings.
• If Reading is accurate calibration is completed. If not, repeat the procedure

• Test the pH level of solution/water and make your living healthier.
• Pocket size, lightweight and portable.
• Very wide variety of applications, used for testing the acidity and alkaline levels of almost any liquid.
• ATC function(Automatic temperature compensation) and clear backlight LCD display.
• Apply in water sources, soil-free growing, aquarium, hydroponics, laboratory, spas, swimming pools and other water systems.

• Measuring range :0.00-14 .00 PH
• Accuracy: +/- 0.1PH
• Resolution: 0.1PH
• Operating temperature: 0 oC~ 50 oC
• Battery: 3X1.5V (AG13 button battery type)  (not including batteries)
• Dimensions: 142mm (L) × 29mm (W) × 15mm (H)
• Weight: 51 Gram

• High Accuracy & Easy to Use: The maximum tolerance is less than +/- 2%, and the operation steps are simple.
• Wide Use: 0-999 PPM measurement range. Ideal tool for testing drinking water, aquariums, RO/DI systems, hydroponics,pool,etc.
• Fast Read & Auto-off Function: Use intelligent detection chip, which can be read on the digital screen of Total Dissolved Solids instrument within one second. After 10 minutes of inactivity, the Meter will automatically turn off to conserve battery power.This product is auto-calibrated and is ready to use
• Do not immerse meter in liquid beyond the maximum immersion level of 4 cm. & Do not store meter in high temperatures or in direct sunlight.
• The large backlight LCD has been upgraded for easy reading, and has an automatic lock function for ease of use.

• PH-009 I pen type pH meter.
• Economical testers are easy-to-use and low cost instruments to measure quick and reliable pH values.
• Pen type meter that can simultaneously measure display pH and temperature results.
• The electrode has been used (laid) for long time from the last calibration.
• The electrode has been used in particularly taxing conditions.
• The utmost accuracy is required.
• Measuring range 0.0 to 14.0 pH.
• Resolution 0.1 pH.
• Accuracy ± 0.1 pH.
• Temperature compensation 0 degree Celsius to 50 degree Celsius.
• Relative humidity maximum 95 percent.
• Batteries 3 x 1.5V AG-13 button batteries (included) protective cap, calibration screw-driver, batteries and instructions.
• 700 hours of use.
• Color as shown in the picture.
• Size 150 x 28 x 16 mm or 5.85 x 1.092 x 0.624 inch.
• Net weight 54 g or 1.89 oz.

Additional Information:

• Delivery Time: 2

• Condition: 100% Brand New
• Material: Plastic
• Salinity measuring range: 0.00ppt-9.99ppt10.0ppt-50ppt
• Resolution: 0.01ppt/0.1ppt
• Accuracy: +1-3%F.S.+/-1 digit
• Instrument Repeatability: +/-0.01ppt/0.1ppt
• Solvent temperature compensation range: 0-60 Temperature accuracy:  +/-1
• Power Supply: LR44 button type battery * 4 (Battery not included)
• Display: Large LCD segment type display
• Working temperature range: 0~50
• Working humidity range: 0%RH~80%RH(non-condensing)
• Size: approx. 177*43*43cm / 7*1.7*1.7in

Additional Information:

• Delivery Time: 2

PH,TDS,TEMP,EC,Salinity,SG,ORP.Features include Supports 3-point calibration automatic identification, water-resistant body, simultaneous temperature display, sleek, lightweight design, a large LCD display, Automatic Temperature Compensation (ATC), Display support backlight, data-hold function, and low-battery indicator.

PH:
Measurement range: 0.01-14.00pH
Resolution: 0.01pH

Accuracy: ±0.05pH

TDS:
Measurement range: 0 to 1000ppm 1000ppm to 10000ppm 10.1 to 200.0ppt

Resolution: 1ppm; 0.1ppt

Accuracy: ±2% of reading

EC:

Measurement range: 0 to10000uS/cm 10.01-19.99ms 20.1-400mS/CM
Resolution: 1 uS/cm; 0.1 mS/CM

Accuracy: ±2% of reading

ORP:
Measurement range: 0~±999mV

S.G:
Measurement range: 1.000~1.222

Salinity:
Measurement range: 0.001 to 25.00%
Resolution: 0.01%
Accuracy: 0.01-5.00% (±0.1%) 5.10-25.00% (±1%)

Digital Water Quality Tester

Calibration:

1.EC:Recognize solution automatically ( 1413us/cm, 12.88mS/cm , 111.8m5/cm) --f the meter can't identify the solution,change the electrode or contact supplier
2.pH: One point or two points or three points automatically-f the meter can't identify the solution, chare the electrode or contact supplier
3. Noted: Always clean the electrode after use

Additional Information:

• Delivery Time: 2

• Condition: 100% Brand New.
• Item Type: Water Quality Tester.
• Material: Plastic.
• Test Range: 0 to10000uS/cm 10.01-19.99ms 20.1-400mS/CM.
• Resolution: 1uS/cm; 0.1mS/CM.
• Accuracy: ±2% of the reading.
• TDS Test Range: 0 to 1000ppm 1000ppm to 10000ppm 10.1 to 200.0ppt
• Resolution: 1ppm; 0.1ppt
• Accuracy: ±2% of the reading
• Salinity Test Range: 0.00 to 25.00%
• Resolution: 0.01
• Accuracy: 0.01-5.00% (±0.1%) 5.10-25.00% (±1%)pH Test Range: 0.01-14.00pH
• Resolution: 0.01pH
• Accuracy: ±0.05pH
• Temperature Compensation: Automatic Temperature Compensation (ATC)Working Environment: 0 to 60.0 (32.0-140 RH 100%
• TDS Factor: 0.4 to 1.0
• Temperature Range: 0.1-60.0 32.0-140
• Temperature Accuracy: ±0.5
• Temperature Resolution: 0.1
• Automatic Power-off: 5 Minutes
• Display: Support Backlight
• Waterproof Grade: IP67
• Power Consumption: 2.9mA, power consumption for shutdown is 0
• Feature: Within 150ppt, the accuracy is relatively accurate, while above 160ppt, the deviation is relatively largeBattery: 3 x LR44 Button Battery (Not Included)Display Screen Size: Approx. 33 x 24 mm / 1.3 x 0.9 inProduct Size: Approx. 183 x 37 x 37 mm / 7.2 x 1.5 x 1.5 inWeight: Approx. 162g / 5.7oz

Additional Information:

• Delivery Time: 2